- 173comments
- 31comments
- 74comments
- 206comments
- 87comments
- 12comments
- 5comments
- 151comments
- 16comments
- 3comments
- 16comments
- 73comments
- —discuss
- 46comments
- 132comments
- 436comments
- 282comments
- 17comments
- 59comments
- 12comments
- 131comments
- 418comments
- 70comments
- 46comments
- 46comments
- 305comments
- 13comments
- 293comments
- 284comments
- 116comments
I got a 503; maybe hugged to death?
https://web.archive.org/web/20260117044133/https://k0lee.com...
I have fixed a couple of washing machines and other appliances over the years. It's satisfying although likely not money-saving unless you don't put a value on your time. But I like working on mechanical things so it's closer to a hobby for me.
Being able to repair my Sears Kenmore 80 Series washing machine from the late 90s has definitely saved me money. I've made exactly two repairs in the last 15 years, each costing me less than $50 dollars in parts, neither taking more than two hours to complete, and both saving me from having to buy a new machine. If that's not money-saving, then I don't know what is!
It surprises me how the US loves their top-loading washers. Here in the UK, there isn't the complex (though interesting) "transmission": the drum has fins to act as both agitator and spin-dryer. This means it's just a boring belt drive between motor and drum (or direct drive, for newer machines.)
Top loaders are higher capacity and cost less. And open air drying is preferable to machine drying.
Top loaders also act as spin dryers...
Front loaders also get moldy and stink because they have to be sealed up so tightly. If you're not there to immediately pull out the clothes after the cycle, you're screwed. And in a small laundry room there isn't always room to let the door stay open to dry out the inside.
In my experience with front-loaders, all of these are non-problems.
But my understanding is that top-loaders are always inefficient: they have to use a lot more water, because the clothes have to be submerged, and thus they also have to use a lot more energy to heat it.
Mainly it's just everybody grew up using top-loaders, though it's also easier to get clothes in and out of a top-loader than a front (unless you have a huge machine). [edit]Oh, and also the up-front cost of a top-loader was about $100 less when I last bought a machine.
I've used a front-loader now for years and the only thing I really miss from my top-loader is that I could just leave the lid open for it to dry out. The door of the front-loader is perennially in the way if you leave it wide open, so we have to prop it open to prevent mildew.
It works well but takes up more space because you can't stack washer/dryer, in Europe apartments and houses are a bit smaller so if you can save a square meter then that's good.
Stacked combo units with a top-load washer on the bottom definitely exist[1].
Whirlpool makes them by combining washer assemblies from Clyde, Ohio and dryer assemblers from Marion, Ohio.
(It's not necessarily the most convenient way to do things, but it is also not a fiction.)
[1]: https://www.whirlpool.com/laundry/laundry-sets/stacked-laund... [scroll down]
I once had top-loader in the bathroom of an apartment that I lived in by myself.
Leaving the lid wide open was a pretty great way of living life. I'd shed my clothes to take a shower and just toss them directly into the washing machine. When it came time to start a load it was a simple matter to put some soap in and push start.
It's my understanding that top loaders are less prone to breakdowns.
and leaks, since there's no door seals to wear out
The primary failure I've observed in washing machines that get a lot of use is the drain pumps which are probably similarly (un)reliable across designs (we only have front loaders so not sure).
I can agree: my parents bought a top loader and dryer in 1975 ('Made in Newton Iowa") which was used a few times a week for 30 years and now once a week for the last 21, as far as I know without repair. Now held by a family member they still look like the day they were delivered due to the porcelain enamel used instead of the painted metal that disintegrated on my second front loader. I've managed to repair my 3 front loaders through an average of about 8yrs each, so far. I've joked with my wife that if I see the washer by the side of the road I'll carry it home on my back.
We have those types here in the States, too. They're very common. We even have several different domestic manufacturers of them to pick from.
(As an aside: I don't throw rocks at your house.)